Mitsubishi E Variable frequency drive (VFD) Instruction Manual – Free ebook download as PDF File .pdf), Text File .txt) or read book online for free. Thank you for choosing this Mitsubishi Inverter. This Instruction Manual provides instructions for advanced use of the FR-E series inverters. Incorrect. 10 Jan Thank you for choosing this Mitsubishi Inverter. This Instruction Manual ( basic) is intended for users who “just want to run the inverter”.

Author: Nemuro Kiran
Country: Dominican Republic
Language: English (Spanish)
Genre: Business
Published (Last): 27 September 2010
Pages: 192
PDF File Size: 19.70 Mb
ePub File Size: 13.49 Mb
ISBN: 135-1-95966-202-5
Downloads: 3894
Price: Free* [*Free Regsitration Required]
Uploader: Mazujin

Selection of operation mode and operation location Parameter 6. Page Shaft is mitsubishi e700 vfd manual. Frequency setting by external terminals Parameter During jog operation or PID control operation, the remote setting function is invalid.

Mitsubishi e700 vfd manual Selection and protection of a motor Parameter NOTES Fault by electronic thermal relay function is reset by inverter power reset and reset signal input. If the Mitwubishi connector is used to make migsubishi connection, use a distributor since a terminating resistor cannot be fitted.

Page S700 the output torque current of the motor Parameter Selection method of general-purpose magnetic flux vector control Perform secure wiring. Number of motor 6. Misoperation prevention and parameter setting restriction Parameter User group function Pr.

Name Description Parameters referred to Value Acceleration and deceleration Parameter Start-time hold function Pr. External operation Basic settings Possible faults: Connection of stand-alone option units Wiring It is recommended to configure a sequence, which shuts off power in the input side of the in- verter by the external thermal relay as shown below, to prevent overheat and burnout of the high duty brake resistor FR-ABR in case the regenerative brake transistor is damaged.

TOP Related Posts  SOMATOMETRIA PEDIATRICA PDF DOWNLOAD

Increase the filter time constant if steady operation cannot be performed due to noise. Page Monitor display and monitor output signals Parameter 6. One to two years of periodic inspection cycle is recommended.

The po- tentiometer is supplied with a voltage of 5V through terminal 10 of the frequency inverter. Set “50”Hz to Pr. From the operation panel Disabled From communication communication option Communication frequency setting Connection of communication option command sending Refer to the corresponding commu- Pr. Leave enough clearances around the inverter refer mitsubishi e700 vfd manual page Check point heck that the frequency of using the brake is proper.

Command source switchover Measurements on the main circuit Maintenance and inspection 8. Got it, continue to print. When stall prevention operation is performed, the OL signal is output. When encasing multiple inverters, install them in parallel as a cooling measure. Enclosure design Installation Arrangement of multiple inverters When multiple inverters are placed in the same enclosure, generally arrange them horizontally as shown in the figure a. Operation mitsubishi e700 vfd manual of the FR-E The number of digits displayed on the operation panel is four.

Connection Of Stand-alone Option Units, Magnetic Contactors mc Connection of stand-alone option units Wiring Mitsubishi e700 vfd manual of stand-alone option units The inverter accepts a variety of stand-alone option units as required. Remote Setting Function pr. Page – Checking the inverter and converter modu Signal Signal tion Tab. Press the SET mitsubishi e700 vfd manual to set.

Mitsubishi Electric FR-E700 Instruction Manual

Simple mode parameter list Basic settings Before performing offline auto tuning Check the following before performing offline auto tuning. It is recommended to install a device to monitor voltage mitsubishi e700 vfd manual checking the power supply mitsubishj to the inverter. Page Frequency setting by analog input terminal 2, 4 Parameter 3.

TOP Related Posts  EL AZAR Y LA NECESIDAD JACQUES MONOD EPUB DOWNLOAD

The motor will coast if enough regenerative energy is given mitsubishi e700 vfd manual the motor. Operation Display Turn the digital dial until P. Output frequency is 3Hz or less Mitsubishi e700 vfd manual frequency Pr.

Failure to observe this mutsubishi lead to injuries. Page Signal Signal tion Tab. Adjust the output torque current of the motor Parameter Selection method of general-purpose magnetic flux vector control Perform secure wiring. When drilling mounting holes in an enclosure etc.

MITSUBISHI ELECTRIC FR-E INSTRUCTION MANUAL Pdf Download.

Therefore, the next query must be made when the inverter processing time has mitsubishi e700 vfd manual after the previous query. If “star connection” is mistaken for “delta connection” or vice versa during setting of Pr. Reset method of protective function Troubleshooting Reset method of protective function Eliminate the cause of the error before you reset the inverter.

Page OFF position changes the terminal 4 to the voltage input specification. NOTE Setting value “1” to “4” can be changed in the easy operation mode. H02 During forward rotation b2: OL overload status b5: